How do I reset my Ubnt NVR?

How do I reset my Ubnt NVR?

Hard Power OFF Press and hold the Power button until the LEDs turn off to immediately turn off the UniFi NVR. Reset Button Resets the UniFi NVR to factory defaults. The UniFi NVR must be fully booted and running. Press and hold the Reset button for about 10 seconds.

How do I reset my UVC G3 Micro?

Steps: UVC-G3-Micro Recovery

1. Disconnect power from the UVC-Micro.
2. Insert a paperclip or similarly narrow object in to the reset hole on the opposing side of the LED and press down.
3. Continue holding this button while you apply power to the UVC-Micro.
4. After approximately 15-20 seconds, the LED will flash once.

How do I access UniFi NVR remotely?

Remote VPN access You can also access your UniFi Video installation by configuring a VPN that directly connects to their setup from the Internet. This requires configuring the VPN through your gateway, as well as setting up the VPN client on the device from which you would like to access the UniFi Video application.

What is Ubiquiti NVR?

The Network Video Recorder Pro (UNVR Pro) is a business-grade network video recorder that provides data redundancy and long-term storage capabilities (up to 60 days of storage for 20 4K cameras or 60 1080p cameras).

How do I reset my UVC NVR?

Hardware Overview Resets the UniFi Video NVR to factory defaults. The UniFi Video NVR must be fully booted and running. Press and hold the Reset button for about 10 seconds. The UniFi Video NVR will automatically reboot with default settings.

How do I reset my UVC Flex G3?

Reset Button The Reset Button is used to reset the camera to factory defaults. Press and hold the Reset Button for more than 10 seconds while the camera is powered on. Use the Base Mount by itself to install the G3 Flex camera on a desktop or tabletop.

How do I access my NVR remotely?

There are 6 steps to setting up your NVR for remote viewing:

1. Understand Your Network.
2. Setup DDNS.
3. Setup A Port Forward.
4. Assign The DDNS Hostname To Your NVR.
5. Set Two IP Addresses For Your NVR.
6. Verify That Local Viewing and Remote Viewing Work.

Is UniFi video discontinued?

From 1st January 2021, the Unifi Video NVR will no longer be offered or supported, More specifically: No software or hardware revisions will be released, including for web UI and mobile applications. All cloud operations will be shut down and video.ui.com will no longer be accessible.

What cameras work with Ubiquiti NVR?

UniFi Protect is compatible with all G2, G3, and G4 cameras and doorbells with the prefix UVC (UVC, UVC-G3, and UVC-G4), as well as all Protect IoT devices with UFP and UP prefixes.

Is UniFi Protect software free?

No Subscription Fees: With UniFi Protect, there are no subscription fees to worry about whatsoever.

How do I troubleshoot a UVC-NVR that is not working?

Follow these steps to troubleshoot: Check the UI Status page to see if there is any issue on our side. Verify that the name of the NVR as shown in the UniFi Video Controller’s Settings matches how it appears in video.ui.com. If the NVR in question was restored from another UVC-NVR, it should be re-adopted.

How do I turn the unifi NVR on and off?

• Power ON Press the Powerbutton to turn on the UniFi NVR and start all services. • Soft Power OFF Briefly press the Power button to stop all services and safely shut down the UniFi NVR. • Hard Power OFF Press and hold the Powerbutton until the LEDs turn off to immediately turn off the UniFi NVR.

Why is my NVR not reaching out to the cloud?

This means that your NVR is not reaching out to Cloud. Follow these steps to troubleshoot: Check the UI Status page to see if there is any issue on our side. Verify that the name of the NVR as shown in the UniFi Video Controller’s Settings matches how it appears in video.ui.com.

Why does my camera keep disconnecting from the NVR?

UniFi Video cameras may disconnect from the NVR for a variety of reasons. Identifying whether the behavior affects specific cameras or all of them, whether the disconnects follow a pattern (such as disconnecting during sunset), or simply remain disconnected, will help identify the root cause of the issue.