Menu Close

What size chain does an Echo CS 370 take?

What size chain does an Echo CS 370 take?

16 inch
5-Pack 16″ Semi Chisel Saw Chain for Echo CS-370 Chainsaws – (16 inch, 3/8″ Low Profile Pitch, 0.050″ Gauge, 56 Drive Links, CSC-S56)

How many cc’s is a Echo CS 370?

36.3
CS-370 Specifications

Engine Displacement (cc) 36.3 9.5
Carburetor Butterfly-Valve Diaphragm Spur
Oiling System Automatic/Adjustable Plastic
Vibration Reduction System Standard 13.9
Available Bar Lengths (in) 16, 18 1 yr commercial / 5 yr consumer

How do you start a new Echo chainsaw?

Restart a warm Echo chainsaw motor by pushing the chain-brake lever toward the tip of the chain bar. Flip the ignition switch to the “Run” position. Place the chainsaw on the ground and pull the starter handle. Immediately press and release the trigger once you hear the motor start idling.

Why does my Echo chainsaw keep stalling?

If the spark arrestor is clogged, the chainsaw may run stall or run rough. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall. If the carburetor is clogged, try cleaning it with carburetor cleaner. If cleaning the carburetor isn’t effective, rebuild or replace the entire carburetor.

What size chainsaw file do I need?

The larger the pitch will mean the higher the cutting teeth will be. The higher the teeth will therefore mean the larger the file will need to be. If you do not know your chainsaw pitch you can gauge it by measuring the distance between three rivets….File sizes.

Chain pitch Round file diameter
3/8″ 5.2mm
.404 5.5mm

Why will my chainsaw not start?

The chainsaw’s engine is flooded with fuel. A fuel issue is one of the most common reasons why a chainsaw won’t start. If you believe fuel has flooded the chainsaw engine, pull the starter cord several times while holding the throttle, dry and replace the spark plug, and then try starting the chainsaw again.

How do you start a cold Echo chainsaw?

❄️ Cold start:

  1. Activate the chain-brake.
  2. switch the on/off switch to the on position.
  3. Activate the choke.
  4. Push the primer bulb 3-8 times.
  5. Pull the starter handle until you hear the engine tends to start.
  6. Switch off the choke.
  7. Pull the start handle again until the engine runs.

How do I select a chainsaw file?

The larger the pitch will mean the higher the cutting teeth will be. The higher the teeth will therefore mean the larger the file will need to be. If you do not know your chainsaw pitch you can gauge it by measuring the distance between three rivets.

How to replace the chain on your Echo chainsaw?

Socket And Wrench

  • Replacement Parts
  • Scrench
  • How to fix an echo chainsaw?

    Start engine and run for several minutes to reach operating temperature.

  • Stop engine.
  • Start engine and turn the high-speed needle (A) rich (CCW) until the engine runs between 13,500 and 14,500 RPM.
  • Idle Speed Adjustment.
  • Accelerate to full throttle for 2-3 seconds to clear excess fuel from engine then return to idle.
  • How to adjust the oiler on an echo chainsaw?

    Release the throttle trigger on your Echo chainsaw to stop the chain rotation.

  • Set the chainsaw on a flat surface. Wait for the engine to cool completely.
  • Turn the chainsaw on its left side,with the guide bar and chain pointing upward.
  • Place newspaper on the ground in an open area.
  • Stop the chainsaw’s engine.
  • What is the gas mixture for an echo chainsaw?

    Use a gas can to make your mix. Your local hardware store should have gas cans designed for two-cycle fuel.

  • Measure the one gallon of unleaded gas you put in the can. Echo recommends using 89 octane fuel.
  • Add 2.6 ounces of two-cycle oil to the gas can.
  • Fill the tank on your chainsaw and get to work.
  • Posted in Advice