Menu Close

How do I find my NETGEAR SSID?

How do I find my NETGEAR SSID?

Netgear: You can typically find the SSID by selecting the Basic settings option, and then selecting Wireless Settings. The SSID may be labeled as Wireless Network Name. The option to enable SSID Broadcast is often located by selecting Wireless Settings under the Advanced settings.

Where is the Wi-Fi password on NETGEAR?

Re: Wifi Password the default wifi password would be on the bottom or back of the router in a label.

How do I change my SSID name NETGEAR?

Launch an Internet browser and type into the address bar.

  1. Enter the router user name and password when prompted.
  2. Click OK.
  3. Select Wireless.
  4. Enter your new network name in the Name (SSID) field.
  5. Enter your new password in the Password (Network Key) fields.
  6. Click the Apply button.

Is the SSID my Wi-Fi password?

The SSID (Service Set Identifier) is the name of your wireless network, also known as Network ID. This is what you will look for when connecting wireless computers and devices. The Password is the secret word or phrase you will enter when first connecting a device to your wireless network.

Is SSID the same as SN?

The default Wi-Fi password or Wireless Key is the number between two bar codes. The Serial Number is the number above two barcodes. In this example, the SSID is 2WIRE110. The default Wi-Fi password or Wireless Network Key is below Mac Address, to the right of the barcode.

How do I configure NETGEAR?

To install your NETGEAR router using the router web interface:

  1. Using an Ethernet cable, connect your modem to the yellow Internet port on the back of your NETGEAR router.
  2. Connect your computer to one of the Ethernet ports on your router.
  3. Press the Power button on the router.
  4. Open a web browser and enter

How do I reset my Netgear router?

How do I reset my NETGEAR cable modem router?

  1. Locate the Reset button on the back of your cable modem router.
  2. Using a paper clip or similar object, press and hold the Reset button for about seven seconds.
  3. Release the Reset button and wait for your cable modem router to reboot. Factory default settings are restored.

What is my network SSID?


  1. From the Apps menu, select “Settings”.
  2. Select “Wi-Fi”.
  3. Within the list of networks, look for the network name listed next to “Connected”. This is your network’s SSID.

What is SSID index in Wi-Fi?

Service Set IDentifier
SSID stands for Service Set IDentifier and is your network’s name. If you open the list of Wi-Fi networks on your laptop or phone, you’ll see a list of SSIDs. Wireless router or access points broadcast SSIDs so nearby devices can find and display any available networks.

How do you find the SSID on a Netgear router?

Locate the label handle at the rear end of C6300 with NETGEAR printed on it,as shown in the below Figure.

  • Pull out the product label to find your WiFi network name (SSID) and Password (Network Key).
  • You can find your WiFi network Name (SSID),and Password (Network Key) on top of the label,as shown in the below figure.
  • How to reset Netgear router to factory default?

    First,In the left-hand menu,under Maintenance,click Backup Settings option.

  • Now,you will be asked to confirm that you want to restore the factory default settings.
  • Then,The netgear router will now reset and you will see the power light on the front go red,then green as the router is reset.
  • What are the default Netgear admin passwords?

    Password for older models: 1234 . NETGEAR ReadyNAS and ReadyDATA products: Username for all models: admin; Password for ReadyNAS OS and ReadyDATA OS: password; Password for RAIDiator firmware: netgear1; Password for Infrant firmware: infrant1 . NETGEAR fully managed switches: Username: admin; Password: These products do not use a default

    How do I change the SSID on my Netgear extender?

    Reset your NETGEAR WiFi Extender back to factory default settings.

  • Connect via WiFi to your NETGEAR WiFi extender (the network name should be “NETGEAR_EXT”)
  • Open up a web browser like Internet Explorer/Firefox and enter into the address (or try You will be prompted to enter a username and password.
  • Posted in Blog