Menu Close

How many tons is a Trane XL20i?

How many tons is a Trane XL20i?

5 Tons
Trane XL20i 5 Tons 20 SEER Variable Speed R-410A Split System Air Conditioner – 4TTV0060A1000B – Ferguson.

Why is my Trane air conditioner not cooling?

Your filters may be clogged or dirty Clean or replace the filters. Consult your local Trane Comfort Specialist™ if you are unsure where the filters are located. Your thermostat controls may be set incorrectly Try turning the thermostat off and then on again. Reset to the desired temperature and see if that helps.

What is Error 126 on Trane thermostat?

Trane thermostat error code 126 Meaning: There might be a low-temperature lockout (the thermostat may have broken the electrical circuit due to ambient outdoor temperature dropping too low). Suggested fix: Try to reset the system.

What does Error 79 mean on a Trane thermostat?

Meaning: As mentioned earlier, Error Code 79 simply says “low pressure switch open”. Causes can be iced evaporator coil, clogged air filter, low refrigerant, or a defective low pressure switch. Potential workaround: Reset the system and check if the error clears.

What seer is a Trane XL20i?

The XL20i’s SEER rating of up to 20.00 is among the highest energy efficiency rating of any air conditioner available today. The XL20i has two compressors: one for milder weather and a second larger compressor for those extremely hot days. It’s like having two units in one.

What is Stage 2 Cooling Trane?

Two stage cooling means the air conditioner or heat pump has a compressor with two levels of operation: high for hot summer days and low for milder days. Since the low setting is adequate to meet household-cooling demands 80% of the time, a two-stage unit runs for longer periods and produces more even temperatures.

Why is my Trane blowing cold air?

Your furnace may be blowing cold air because the filter is too dirty. A dirty air filter blocks airflow over the furnace’s heat exchanger, causing it to overheat. When overheating, your furnace can trip a high limit switch, causing the furnace burners to shut off so that the heat exchanger does not crack.

How do you reset a Trane thermostat?

All Thermostat Models

  2. Locate the switch for your thermostat in the breaker box.
  3. Flip the switch to the OFF position for 20-30 seconds.
  4. Return the switch to the ON position.
  5. The reboot process will take several minutes to complete.

How do you clear a Trane error code?

To have your Trane air conditioner reset (and clear an error code), all you need to do is simply reset the circuit breaker. We suggest you wait a couple of minutes before restarting the unit.

Does a 2 stage AC run all the time?

A two stage AC offers two levels: high and low. A two stage unit runs at full capacity when you need it to and at a lower level when you don’t. Two stage units don’t run as continuously as a variable speed AC, but they do cycle on and off less frequently than single stage systems.

Why install a Trane xl20i air conditioner?

When installed in a Trane communicating system, your XL20i air conditioner can be part of a hard working team dedicated to your comfort. In a Trane communicating system, every component is in constant digital communication with every other, allowing the entire system to learn as it operates, optimizing itself for comfort and efficiency.

How many pages are in the Trane xl20i heat pump manual?

50 hz package heat pump units 30, 40, 50 mbh (28 pages) Heat Pump Trane 4TWR4 Installer’s Manual Heat pumps (8 pages) Heat Pump Trane WSC060-120 User Manual Packaged heat pumps (53 pages) Summary of Contents for Trane XL20i 4TTZ0024A1 Page 1: Product Data

What is Trane xl20i 4ttz0024a1?

Trane XL20i 4TTZ0024A1 Product Data Split system cooling xl20i 4ttz0024, 036, 048 & 060 with comfortlink 2, 3, 4 & 5 tons Hide thumbs

How to contact Trane equipment manuals-Bay area services?

Trane Equipment Manuals – Bay Area Services (920) [email protected] Home About Our Company Careers Specials Our Blog Find Our Showroom Contact Service & Maintenance

Posted in Life